What's New: Week of 09/01/2024

Made to Order.

For tying stone or CMU walls together. Specify thickness, length, width, bend length, split bend length and steel type.

Available in Type 304 and Type 316 Stainless Steel

Thickness: 3/8", 1/4", 3/16", 1/8", 12 gauge, 14 gauge, 16 gauge

Made to Order

Available Rod Diameters: 1/4", 3/8", 1/2", 5/8", 3/4"

Specify diameter and length of rod, thread length, length of top "T" portion and steel type.

Available in Type 304 Stainless Steel

Made to Order

Specify thickness, length, width, notch dimensions and location, threaded rod diameter, rod length beyond anchor and steel type.

Available in Stainless Steel and Hot Dip Galvanized.

Made to Order.

Corrugated Strap typically embedded in a masonry wall with the welded threaded rod extending out from the wall.

Specify thickness, length and width of corrugated strap, diameter and length of welded threaded rod and steel type.

Available in Stainless Steel and Hot Dip Galvanized.

Made to Order.

Specify thickness, strap length, width, pin diameter and length, location of pin, diameter of threaded rod, length of threaded rod beyond strap and steel type.

Available in Stainless Steel and Hot Dip Galvanized.

Made to Order.

Specify thickness, strap length, width, bend length, diameter of threaded rod, length of threaded rod beyond strap and steel type.

Available in Stainless Steel and Hot Dip Galvanized.

Made to Order

Used to level and plumb stone. Shims can be cut to any size which combines high compression strength and superior load bearing surface contact characteristics.

Specify thickness, length, width and steel type.

Available in Type 304 Stainless Steel and Plain Steel.

Thickness: 1/2", 3/8", 1/4", 3/16", 1/8", 12 gauge, 14 gauge, 16 gauge.

Made to Order.

Specify thickness, strap length, width, split bend length, diameter of threaded rod, length of threaded rod beyond strap and steel type.

Available in Stainless Steel and Hot Dip Galvanized.

Used to level and plumb stone. Shims are molded from an engineered copolymer plastic material which combines high compression strength and superior load bearing surface contact characteristics.

Available in 2" x 2" in 1/16", 1/8", 1/4" 3/8" and 1" x 1" in 3/8"

MADE TO ORDER

Thickness: 3/8", 1/4", 3/16", 1/8", 11 gage, 12 gage, & 14 gage.

Strap Width: 1-1/4" minimum recommended. Minimum width for 1/4" thick is 2" wide.

Length: Specify length as the outside dimensions between the bends. Bend with Hole: 1" minimum recommended. You should consider the overall length of the anchor and the height of the split bend to make sure there is enough room for the installer to get the screw and tool in place without interference from the split bend.

Hole should be a minimum of 1/16" larger than your screw size. (3/8" screw will use a 7/16" diameter hole).

Split Bend: Minimum 3/4" recommended (specify as o.d. dimension) Available in Type 304 and Type 316 Stainless Steel, Zinc Alloy 710 Firewall Material

Made to Order

Thickness: 3/8", 1/4", 3/16", 1/8", 11 gage, 12 gage, & 14 gage.

Strap Width: 1-1/4" minimum recommended.

Length: Specify length as the outside dimensions between the bends.

Bend with Hole: 1" minimum recommended. You should consider the overall length of the anchor and the height of the bend to make sure there is enough room for the installer to get the screw and tool in place without interference from the U-Bend. Hole should be minimum of 1/16" larger than your screw size. (3/8" screw will use a 7/16" diameter hole).

Bend Length: Minimum 3/4" recommended (specify as o.d. dimension)

Available in Type 304 and Type 316 Stainless Steel and Zinc Alloy 710 Firewall Material.

Made to Order

Thickness: 3/8", 1/4", 3/16", 1/8", 11 gauge, 12 gauge, & 14 gauge.

Width: 1-1/4" minimum recommended.Length: Specify length as the outside dimensions between the bends.

Bend with Hole: 1" minimum recommended. You should consider the overall length of the anchor and the height of the bend to make sure there is enough room for the installer to get the screw and tool in place without interference from the U-Bend. Hole should be minimum of 1/16" larger than your screw size. (3/8" screw will use a 7/16" diameter hole).

Bend Length: Minimum 3/4" recommended (specify as o.d. dimension)

Available in Type 304 and Type 316 Stainless Steel, Zinc Alloy 710 Firewall material

Made to Order

Thickness of Strap: 3/8", 1/4", 3/16", 1/8", 12 gauge, 14 gauge & 16 gauge.

Diameter of Pin: 1/4", 3/8", 1/2", 5/8" Strap Width: 1-1/4" minimum recommended.

Length: Specify length of strap to o.d. of bend and overall length of pin.

Bend Length: minimum 3/4" recommended (specify o.d. dimension)

Available in Type 304 and Type 316 Stainless Steel

Bend Hole: Usually centered in bend. Hole should be 1/16" larger than screw/expansion anchor. (i.e. If using a 1/4" screw the hole diameter would be 5/16".)

Specify Location of Pin from center of pin to end. 1/2" minimum of steel between end of anchor and start of hole is recommended.

Pins are available loose or welded in place.

Made to Order

Specify thickness, length, width, bend length, hole diameter and location, welded plate height and steel type.

Available in Type 304 and Type 316 Stainless Steel

Made to Order

Used for anchoring stone to backups.

Thickness: 1/2", 3/8", 1/4", 3/16", 1/8", 11 gauge, 12 gauge, & 14 gauge.

Strap Width: 2-1/2" minimum recommended.

Length: Specify length as the outside dimension of the bend with the slot.

Bend with Holes: Specify outside dimension and the diameter and location of holes in the bend.

Available in Type 304 and Type 316 Stainless Steelxasd

Made to Order

Used for anchoring stone to backups.

Specify thickness, width (3" minimum recommended), length, bend with holes, hole diameter(s) and location(s), split bend dimensions and steel type.

Available in Type 304 and Type 316 Stainless Steel

Made to Order.

Used for stone attachments. The drilled and tapped Barrel is 5/8" or 3/4" diameter x minimum 3" long with a 3/8" (9.5 mm) diameter continuous threaded rod cut to desired length. Type 304 Stainless Steel.

Special Sizes Available, but barrel diameter should always be a minimum of 3/8" diameter larger than the diameter of the threaded rod.

Made to Order

Angle Clip for various attachments.

#341: Specify thickness, length, width, bend length, hole size and location and steel type.

Available in Stainless Steel, Hot Dip Galvanized, Mill Galvanized (max 1/8"), Plain Steel and Zinc Alloy 710 FIrewall (1/8" and 16 gauge only)

Made to Order

Angle Clip for various attachments.

#341-A: Specify thickness, length, width, bend length, hole sizes and locations and steel type.

Available in Stainless Steel, Hot Dip Galvanized, Mill Galvanized (max 1/8"), Plain Steel and Zinc Alloy 710 Firewall (1/8" and 16 gauge only)

Made to Order

Angle Clip for various attachments.

#341-B: Specify thickness, length, width, bend length, hole size and location, slot size and location and steel type.

Available in Stainless Steel, Hot Dip Galvanized, Mill Galvanized (max 1/8"), Plain Steel and Zinc Alloy 710 FIrewall (1/8" and 16 gauge only)

Made to Order.

Used for attaching masonry to various backups. Bend can be attached to the backup wall by drilling a hole, welding or powder actuated tool.

#342-A: Specify thickness, length, width, bend length, hole size and location, slot size and location and steel type.

Made to Order.

Used for attaching masonry to various backups. Bend can be attached to the backup wall by drilling a hole, welding or powder actuated tool.

#342: Specify thickness, length, width, bend length, slot size and location and steel type.

Made to Order.

Used for attaching masonry to various backups. Bend can be attached to the backup wall by drilling a hole, welding or powder actuated tool.

#342-B: Specify thickness, length, width, bend length, slot sizes and locations and steel type.

Used to attach a stone panel in between two installed stone panels.

Specify diameter of dowel, length of dowel. Spring length beyond dowel should be the same length as the dowel. The spring compresses to have its length.

Type 304 Stainless Steel.

Stock Sizes:

1/2" diameter and 3/8" diameter x 4" dowel with 4" spring

1/2" diameter and 3/8" diameter x 3" dowel with 3" spring

Custom lengths available

Wire tie anchor used to secure rubble stone veneers to back-up walls. Used with Heckmann's Rubble Stone Veneer Anchor system (#398-C L-Type Rubble clips and #398-J J-Hook Rod). Ideal for when horizontal mortar joints do not align, and a large amount of vertical adjustment is required.

The 398 wire tie is 3/16" diameter. welded rod prevents compression loads from damaging sheathing. Specify tie length.

Available in Stainless Steel and Hot Dip Galvanized

L-Type anchor used to secure rubble stone veneers to back-up walls. Used with Heckmann's Rubble Stone Veneer Anchor system (#398 Rubble Stone Wire Tie and #398-J J-Hook Rod). Ideal for when horizontal mortar joints do not align, and a large amount of vertical adjustment is required.

The 398-C Clip is 12 gauge x 2-3/4" wide. Specify the Length required. The J-Rod is lowered through the slots and require the 398 ties to be pre-loaded between the clips. Clips are typically spaced 16" x 16" or 16" x 24".

Available in Stainless Steel and Hot Dip Galvanized.

J-Hook Rod used to secure rubble stone veneers to back-up walls. Used with Heckmann's Rubble Stone Veneer Anchor system (#398-C L-Type Rubble clips and #398 Rubble Stone Wire Tie). Ideal for when horizontal mortar joints do not align, and a large amount of vertical adjustment is required.

J-Hook Rod: Available in 5/16" and 3/8" diameter typically 52" long. These are inserted down through the 398-C Clips after pre-loading the 398 wire ties between the clips.

Available in Stainless Steel and Hot Dip Galvanized.

Made to Order

Used to attach stone, structural members, veneers, or equipment to concrete structures. Plates and Angles can also be used to frame openings in concrete walls or as shelf angles. Use with precast or cast-in-place concrete. Custom fabricated to your design requirements. Specify angle leg dimensions, thickness, and length.

Made to Order

Used to attach stone, structural members, veneers, or equipment to concrete structures. Plates and Angles can also be used to frame openings in concrete walls or as shelf angles. Use with precast or cast-in-place concrete. Custom fabricated to your design requirements. Specify plate length, width, thickness, diameter and length of headed anchors, and steel type.

Made to Order

Used to attach stone, structural members, veneers, or equipment to concrete structures. Plates and Angles can also be used to frame openings in concrete walls or as shelf angles. Use with precast or cast-in-place concrete. Custom fabricated to your design requirements. Specify length, width, thickness, and hole diameters and locations.

Made to Order

Used to attach stone, structural members, veneers, or equipment to concrete structures. Plates and Angles can also be used to frame openings in concrete walls or as shelf angles. Use with precast or cast-in-place concrete. Custom fabricated to your design requirements. Specify length, width, thickness, hole diameters and locations, and toe bar dimensions and location.

Made to Order

Used to attach stone, structural members, veneers, or equipment to concrete structures. Plates and Angles can also be used to frame openings in concrete walls or as shelf angles. Use with precast or cast-in-place concrete. Custom fabricated to your design requirements. Specify bend dimensions, slot sizes and locations, od length between bends, width of angle, and steel type.

Made To Order

Used to attach stone, structural members, veneers, or equipment to concrete structures. Plates and Angles can also be used to frame openings in concrete walls or as shelf angles. Use with precast or cast-in-place concrete. Custom fabricated to your design requirements. Specify bend dimensions, slot sizes and locations, od length between bends, width of angle, and steel type.

3/8" diameter x 1-3/4" Long featuring a Type 304 Stainless Steel bolt and a Type 10-8 Stainless Washer with a Brass 260 Alloy sleeve and cone.

Ideal for attaching Stainless Stone Anchors to backups of CMU, Concrete or Brick.

Custom Made

Available in "Z" shape or "U" shape.

Specify Gauge, width, Length, Bend length with hole diameters and locations, bend down length.

Available Type 304 and Type 316 Stainless Steel.

Allows for lateral adjustment for stones with kerfs.

Made to Order - See Submittal Sheet below under References for product details.

Available in type 304 or type 316 stainless steel only.

Allows for lateral adjustment for stones with kerfs.

Made to Order - See Submittal Sheet below under References for product details.

Available in type 304 or type 316 stainless steel only.

Used for attaching brick veneer to backups in seismic zones requiring a reinforcement wire in the exterior brick veneer. The corrugated end increases adhesion in the mortar joint.
(They can be used in non-seismic walls as regular sheet metal veneer anchors without the seismic wire in the exterior veneer wall. )

Raised tab in flat section allows for placement of Pencil Rod or Masonry Wall Reinforcement that allows for in plane horizontal and vertical movement of the masonry walls while restraining tension and compression.

14 gauge x 1-1/4" wide plus a 1-1/2" bend with a centered 5/16" diameter hole.

Type 304 Stainless Steel.

Available in overall lengths of 2-1/2" 3", 3-1/2", 4", 4-1/2", 5", 5-1/2", 6", 7" and 8".

Plastic clip for attaching any 3/16" or 9 gauge masonry veneer anchor to a single horizontal reinforcing wire in the veneer.

9 gauge or 3/16" dia x 10 ft long.

Stainless Steel, Hot Dip Galvanized

See #363 Plastic Seismic Clip for attachment of Continuous wire to wire veneer ties.

As a Partition Wall Stabilizing Anchor, the Dovetail Rod Anchor is Hotdip Galvanized After Fabrication and is used with a #421 plastic tube. When the block core is filled with grout, the tube allows for vertical deflection. The concrete slab above must have a cast-in-place dovetail anchor slot. Standard Rod when used as a Stabilizing Wall Anchor is 3/8" diameter x 7" long and is not threaded. The welded clip is12 gauge.

Catalog # 121-7H - Standard Hotdip Galvanized After Fabrication.

The #121 Dovetail Threaded Rod Anchor can also be used in veneer walls with concrete backups for bolting back to the backup wall.

Custom rod lengths and diameters are available in Type 304 or Type 316 Stainless Steel.

This anchor is installed by either welding the plate to a structural beam or fastening it to a concrete slab with expansion anchors. The plastic tube is grouted into the CMU cell.

Standard: 3/16" x 1-1/2" wide x 3" long plate with a welded 3/8" diameter x 6-3/4" rod. Two 5/16" diameter holes in the plate for attachment.

Standard size is boxed with the #421 Plastic Tube 5/8" od x 7-1/4" with a compressible filler at the end to prevent grout infiltration. Hot Dip Galvanized.

Custom Sizes are available - order 421 Tubes separately for custom sizes.

This plastic tube is used with #121 Dovetail Rod Anchor and the #419 Pin Stabilizing Anchor. The plastic tube has a foam filler on one end to prevent grout penetration. The rods placed into the tube and the tubes are grouted into the CMU. This allows for vertical deflection of the wall.

Used to resist lateral loads at the top of a masonry wall and allow for vertical deflection. Steel bends will be visible at the top of the CMU wall. Standard is 12 gauge x 8" long with 2" bends and 5/16" holes for block sizes 4", 6", 8", 10" and 12". Available in Mill Galvanized Steel and Hotdip Galvanized After Fabrication. Custom Sizes available. Stainless Steel available.

Used to attach CMU walls to structural steel beams

Order in pairs, one left and one right side anchor

Standard size: 7" L x 2" W, 1/8" thick with a 1-1/2" L-shaped bend

Standard Notch: 5/8" W x 1" D, begins 1" from end of anchor

Available in Stainless Steel and Zinc Alloy 710 Firewall (1/8" only)

Made to Order

Thickness: 3/8", 1/4", 3/16", 1/8", 11 gage, 12 gage, & 14 gage.

Strap Width: 1-1/4" minimum recommended. Minimum width for 1/4" thick is 2" wide.

Length: Specify length as the outside dimensions between the bends. Bend with Hole: 1" minimum recommended. You should consider the overall length of the anchor and the height of the split bend to make sure there is enough room for the installer to get the screw and tool in place without interference from the split bend.

Hole should be a minimum of 1/16" larger than your screw size. (3/8" screw will use a 7/16" diameter hole).

Split Bend: Minimum 3/4" recommended (specify as o.d. dimension) Available in Type 304 and Type 316 Stainless Steel, Zinc Alloy 710 Firewall Material

Made to Order

Angle Clip for various attachments.

#341: Specify thickness, length, width, bend length, hole size and location and steel type.

Available in Stainless Steel, Hot Dip Galvanized, Mill Galvanized (max 1/8"), Plain Steel and Zinc Alloy 710 FIrewall (1/8" and 16 gauge only)

Made to Order

Angle Clip for various attachments.

#341-A: Specify thickness, length, width, bend length, hole sizes and locations and steel type.

Available in Stainless Steel, Hot Dip Galvanized, Mill Galvanized (max 1/8"), Plain Steel and Zinc Alloy 710 Firewall (1/8" and 16 gauge only)

Made to Order

Angle Clip for various attachments.

#341-B: Specify thickness, length, width, bend length, hole size and location, slot size and location and steel type.

Available in Stainless Steel, Hot Dip Galvanized, Mill Galvanized (max 1/8"), Plain Steel and Zinc Alloy 710 FIrewall (1/8" and 16 gauge only)

Made to Order.

Used for attaching masonry to various backups. Bend can be attached to the backup wall by drilling a hole, welding or powder actuated tool.

#342-A: Specify thickness, length, width, bend length, hole size and location, slot size and location and steel type.

Made to Order.

Used for attaching masonry to various backups. Bend can be attached to the backup wall by drilling a hole, welding or powder actuated tool.

#342: Specify thickness, length, width, bend length, slot size and location and steel type.

Made to Order.

Used for attaching masonry to various backups. Bend can be attached to the backup wall by drilling a hole, welding or powder actuated tool.

#342-B: Specify thickness, length, width, bend length, slot sizes and locations and steel type.

Made to Order

Efficiently transfers horizontal forces between a masonry wall and the building frame. The Twist-On Anchor allows you to connect a masonry wall to a Joist, Joist Girder or any other Truss as well as to a Castellated or Rolled Beam while allowing free deflection.

3-1/4" wide. Specify anchor length, vertical sliding bar dimension (1/2", 3/4" or 1") and steel type. Vertical Rod can be round or square.

Stainless Steel available in 3/16" or 1/8" thickness.

Zinc Alloy 710 Firewall available in 1/8" only.

Used to center vertical rebar in CMU walls before grout is poured.

9 gauge wire: Two block sizes 8" and 12"

Used to center vertical rebar in CMU walls before grout is poured.

9 gauge wire: Two Block Sizes 8" and 12".

Available in Hot Dip Galvanized.

Made to Order

Used to level and plumb stone. Shims can be cut to any size which combines high compression strength and superior load bearing surface contact characteristics.

Specify thickness, length, width and steel type.

Available in Type 304 Stainless Steel and Plain Steel.

Thickness: 1/2", 3/8", 1/4", 3/16", 1/8", 12 gauge, 14 gauge, 16 gauge.

Used to level and plumb stone. Shims are molded from an engineered copolymer plastic material which combines high compression strength and superior load bearing surface contact characteristics.

Available in 2" x 2" in 1/16", 1/8", 1/4" 3/8" and 1" x 1" in 3/8"

When cast into concrete, Shelf Angle Wedge Inserts and Askew Head Bolts provide a secure and adjustable method for fastening shelf angles and other materials to concrete structures. The inserts allow vertical adjustment so veneers can be properly aligned despite construction tolerances in the building frame.

For 3/4" Bolts only. Malleable Iron Inserts Hot Dip Galvanized

Two Sizes:
Regular: Overall Height 3-7/8" with 1-3/4" vertical adjustment
Long: Overall Height 5-1/2" with 3" vertical adjustment

See product 427 Askew Head Bolts for the bolts.

When cast into concrete, Shelf Angle Wedge Inserts and Askew Head Bolts provide a secure and adjustable method for fastening shelf angles and other materials to concrete structures.

Askew Head Bolts are available 3/4" diameter, Hotdip Galvanized After Fabrication in lengths of 2", 2-1/2", 3", 4" and 6".

See #425 for the Shelf Angle Insert.

Sold with or without #685-75H Hotdip Washers and #681-75H Hotdip Nuts

See 442 Plastic Horse-Shoe Shim Washers and 443 Steel Horse-Shoe Shim Washers for the shims.

Used to shim shelf angles when concrete walls are not plumb.

High Impact multi-polymer plastic shims with compressive strength between 8,000 and 10,000 psi.

Used for shimming anchors and angles for out-of-plumb walls.

Standard stock sizes are 4" x 3" Hotdip Galvanized with a 13/16" x 3" slot in thicknesses of 1/16", 1/8", 1/4", 3/8" and 1/2".

Custom sizes are available in Stainless Steel, Plain Steel, Hotdip Galvanized, or Mill Galvanized (1/16" and 1/8" only for mill galv).

Rubber control joints are used to permit longitudinal movement while allowing expansion and contraction of the masonry wall.

352-14 T-Type - 2-5/8"

352-13 standard 11-1/8"

352-12 standard 6-7/8"

352-11 standard 2-5/8"

Individual joints are 48" long.

Used in vertical or horizontal applications to provide expansion in joints and prevent unwanted clogging with mortar.

3" wide rolls - 50 ft per roll

Thickness: 1/4", 3/8" and 1/2"

Available with or without adhesive

Control Joint Anchors are designed to transfer loads across control joints. They are also intended to handle compression loads and control lateral movement.

22 gauge x 1-1/2" wide x 10" overall length.

Available
Stainless Steel / Plastic
Type 304 all Stainless Steel
Mill Galvanized

Cell vents are installed in the bottom vertical mortar joint of a brick veneer wall to allow moisture to vent out of a cavity wall. Cell vents are also installed at the top of the wall to allow ventilation in the cavity. They consist of many small adjacent passageways, which allow moisture to vent from the cavity to the exterior of the building while restricting ingress of insects. The cellular composition provides easy drainage for moisture along the full height of the head joint. Cell vents are UV-resistant and tested in conformance to ASTM D2240, D790B, D638 and D1238B.

Regular Size: 3/8" thick x 2-1/2" high x 3-3/8 deep.
Jumbo Size: 3/8" thick x 3-1/2" high x 3-3/8" deep.

Available in Tan, Brown, Clear, Cocoa, Black, White and Gray

Louvered Weep Vents come in three sizes: Standard (85LSTD) 2-1/2", Medium (85LCSR) 2-3/4" and Jumbo (i5LJUM) 3-5/8". Louvered front allows water to leave and not re-enter. Available in Gray only.

200 pcs per box.

Used as flashing material to prevent water damage. The standard 1/2" drip-edge is folded back to prevent sharp edge on exterior of wall. Available in Stainless Steel.

Standard is 3" wide x 8 ft in 26 gauge. Custom widths are available.

For securing flashing to a backup wall.

Standards:

1050-T1-SS: 1/8" x 1" wide x 8ft Stainless - no lip
1050-T2-P 1/8" x 1" wide x 8ft - plastic - with lip
1050-T1-A 14 gauge x 1" x 8ft Aluminum - no lip
1050-T2-A 14 gauge x 1" x 8ft Aluminum - with lip
1050-T2-SS 26 gauge x 1-1/2" wide x 8ft - with lip

Custom Sizes available

Specify thickness, width, length, hole size, hole spacing and steel type.

Weep-Thru Mortar Deflector is designed to catch mortar droppings and allow masonry cavity drainage through the weep holes. It has a three dimensional geometric patterned core and is designed to be 10 inches (25.4 cm) high in the cavity wall.

• Allows cavity drainage and protects flashing.

• Dovetail configuration allows mortar droppings to rest on two levels crating open areas for
  proper water drainage.

• When properly installed, will prevent clogging of weep holes.

• Will not grow mold.

• Polymer core is resistant to most known corrosive chemicals, including solvents.

• 10 inch width suspends mortar droppings above the weep holes, but below the flashing
  connection to the interior wall.

• Easy installation. No mechanical fasteners required. Lay first 2 courses of brick and then install Mortar deflector in cavity.

• Packaged in boxes of 5 foot pcs.
  
  

Catalog #84-5 - 1/2" thick (Actual .4") - 50 pcs per box

Catalog # 84-1 - 1" thick - 20 pcs per box

Catalog # 84-2 - 2" thick - 20 pcs per box

Prefabricated soldered Outside Corner Flashing is placed underneath wall flashing for protection from moisture penetration into the building interior.

STANDARD:

* 237-S 10" x 10" x 4" Stainless Corner

SPECIALS:

* 237-C 10" x 10" x 4" Copper Corner

* 2372-S 12" x 12" x 3" Stainless Drip Edge

* 2372-C 12" x 12" x 3" Copper Drip Edge

Prefabricated soldered Inside Corner Flashing is placed underneath wall flashing for protection from moisture penetration into the building interior.

26 gauge stainless steel
16 oz (24 gauge) copper
24 gauge Mill Galvanized

STANDARD:
* 238-S 6" x 4" x 4" Stainless Steel Corner

SPECIALS:
* 238-C 6" x 4" x 4" Copper Corner

* 2382-S 12" x 12" x 3" Stainless Drip Edge

* 2382-C 12" x 12" x 3" Copper Drip Edge

* 238-G 4-7/8" x 4-7/8" x 4" 24 gauge Mill Galv Corner

Prefabricated soldered End Dam is placed underneath wall flashing for protection from moisture penetration into the building interior.

STANDARD:

* 239-S 4" x 4" x 4" 26 gauge Stainless Steel

SPECIAL:

* 239-C 4" x 4" x 4" 16 oz (24 gauge) Copper

Made to Order

Used to level and plumb stone. Shims can be cut to any size which combines high compression strength and superior load bearing surface contact characteristics.

Specify thickness, length, width and steel type.

Available in Type 304 Stainless Steel and Plain Steel.

Thickness: 1/2", 3/8", 1/4", 3/16", 1/8", 12 gauge, 14 gauge, 16 gauge.

Used to level and plumb stone. Shims are molded from an engineered copolymer plastic material which combines high compression strength and superior load bearing surface contact characteristics.

Available in 2" x 2" in 1/16", 1/8", 1/4" 3/8" and 1" x 1" in 3/8"

Remedial Wall Tie provides a quick, effective and economical solution for securing and stabilizing masonry. Existing facades constructed of brick, stone, masonry, precast concrete, etc. that have wall ties missing or corroded, can be re-attached using Remedial Tie without removing the veneer. This stainless-steel helical tie is dry set. The Remedial Tie cuts a threaded groove into the masonry as it is driven into position through a pre-drilled pilot hole. The end result is a strong and permanent connection between wythes without the use of toxic adhesives or rigid mechanical connectors

Stainless Steel

Installation tool for #391 Helix Remedial Ties

391-8mmTOOL - 8 mm ties
391-10mmTOOL - 10 mm ties

Glass Block Panel Anchors are used to tie the glass block to the jambs and head. They are installed at both jams under the expansion strip in every other course.

Made to Order

Specify length, width, thickness, centered hole diameter and steel type.

Available in Type 304 Stainless Steel, Type 316 Stainless Steel and Plain Steel.

Available Thickness: 14 gauge, 12 gauge, 1/8", 3/16", 1/4", 3/8" x 1/2"

3/8" diameter x 1-3/4" Long featuring a Type 304 Stainless Steel bolt and a Type 10-8 Stainless Washer with a Brass 260 Alloy sleeve and cone.

Ideal for attaching Stainless Stone Anchors to backups of CMU, Concrete or Brick.

TOGGLER® was founded in 1968 and is the only manufacturer that designs, patents, and makes all of its anchors in the USA

• SNAPTOGGLE® Heavy-Duty Toggle Bolts

• SnapSkru® Self-Drilling Drywall Anchors

• ALLIGATOR® All-Purpose Anchors

• TOGGLER® Plastic Toggle Anchors

• TOGGLER® Specialty Anchors

Family-owned and established in 1952
High-performance anchors you can trust engineered here in the USA. We never compromise on quality. So you don't.Expansion Anchors

• Drive Pin Anchors

• Threaded Anchors

• Drop-in and Shield Anchors

• Hollow-wall Anchors

• Drill Bits for Concrete

• Adhesive Anchors

• Concrete Accessories

Interna-Rail® aluminum handrail systems are sleek, strong and durable.  In-line fittings make this aluminum handrail system easy-to-install, and produce a striking architectural appearance. The offset panel attachment provides an uninterrupted infill panel railing system allowing the architect to feature their panel design as the focal point.

Interna-Rail Aluminum Handrail Features and Benefits Include:

• In-line fittings provide easy installation

• Offers a smooth architectural appearance

• Fitting-based system allows some reconfiguration options on site

• Shipped in pre-fabricated sections of 10 – 24 feet, easily installed by non-specialized labor

• Extremely non-corrosive and low maintenance when compared to steel handrails

Hollaender's VUE™ railing for glass and acrylic infill panels offers what architects and owners the two most desirable features:

• Transparency

• Visibility

The VUE™ handrail system is a post mounted glass system where the glass panels are held at the posts, not the top and bottom rails. This minimizes the number of horizontal rails in the system which maximizes visibility.

Unlike most post-captured glass railing systems on the market, this railing frame is made of anodized aluminum, not stainless steel, resulting in much lower cost-per-foot. Additional cost savings are created due to the fact that no holes are required in the glass as all glass panels are supported at the bottom.

In addition, the VUE system, which uses 3/8" glass, is also less costly compared to shoe mounted structural glass, which must use ½" glass to meet codes.

The QUAD™ railing system is a rectangular post mounted glass system where the glass panels are captured and held at the posts, rather than being mounted at the top and bottom rails as in other systems. This minimizes the number of horizontal rails in the system to allow for maximum visibility. The rectangular posts provide clean lines throughout the system and can be integrated with a grabrail. The QUAD™ railing system is available in both aluminum and stainless steel. The aluminum system provides the ultimate selection in finishes, as the aluminum can have an anodized finish; as well as a powder coated finish.

Hollaender's KLEAR™ railing system for glass offers architects and owners another option when specifying or designing glass railing systems. They provide two very desirable features:

• Transparency

• Visibility

This system uses the glass infill up to the 42" height requirement and does not have a top cap on the glass: The glass is held at the post—not top and bottom—thus minimizing the number of horizontal rails in the system and maximizing visibility.

Posts are attached with a grab rail or handrail at 36" above the walking surface on level, ramp, and stair railings.

While maintaining structural integrity, this glass railing with no top cap provides more visibility than competitive railing systems.

VISION™ railing system is available in both aluminum and stainless steel. The VISION system is designed with “in-line" clips that support the infill panel. Although the standard infill is glass, metal infills in stainless steel are available in wire mesh and perforated designs, with 304 SS as standard or 316 SS as an option. Acrylic and other custom infill materials are also available. Glass or other infill panels are retained by 4 rounded panel clips. Glass panels will have holes for the bottom 2 clips. Glass infill is available in 3/8" monolithic or 7/16" laminated glass.  Assist rails in aluminum and stainless steel are available for stairs or for level railing as on option.

Hollaender produces ADA compliant handrails, wall rails, and assist rails. Our aluminum component-based (non-welded) handrail systems are made of corrosion resistant aluminum and are easy-to-install. Railings can be shipped as either kits (less engineering and faster lead time) or as fully engineered and fabricated systems.  Handrail systems are available in clear, dark bronze, or black anodized finish. Aluminum component systems typically have a lower cost per linear foot than stainless steel systems.

All railings meet IBC and ADA codes, with 1 ½" IPS heavy wall posts and 1 ¼" or 1 ½" IPS assist rails. If UFAS approval is required, 1" IPS assist rails can be used.

Our Speed-Rail® railing systems look great, is easy-to-install, and is made of the most corrosive resistant aluminum alloy available on the market.  Unlike welded alternatives, our railing systems are easy to install with no special expertise needed, and are very easy to reconfigure on-the-fly.

Speed-Rail® Hand Railing Systems - Features and Benefits

• "Kit of Parts" design allows for on-site assembly, easy to reconfigure when drawings do not match site

• Unique "Industrial Chic" look is ideal for urban or industrial aesthetic

• Easy-to-install with no special expertise required

• Anodized aluminum pipe and aluminum magnesium fittings are extremely corrosion resistant, allowing for the lowest long-term maintenance cost

Speed-Rail® Quik Connect™ kits are a 100% aluminum wire mesh modular railing system that incorporates Speed-Rail® slip-on fittings, providing unrivaled railing strength with easy assembly and installation. Available in 9 simple configurations.

Speed-Rail® Quik Connect™ Aluminum Handrail Features and Benefits Include:

• "Kit of Parts" design allows for on-site assembly

• Rails constructed from 1-1/2 inch Schedule 40 Anodized Aluminum (1.9 inch O.D.)

• Posts constructed from 1-1/2 inch Schedule 80 Anodized Aluminum (1.9 inch O.D.)

• Anodized aluminum pipe and aluminum magnesium fittings are extremely corrosion resistant, allowing for the lowest long-term maintenance cost

• Aluminum wire mesh panels are 2-inch square providing both strength and visibility. Panels are constructed from:

- 3/16 diameter Aluminum Lock Crimp Wire Mesh

- 1/8" Aluminum U-Channel with Mitered and Welded Corners 

- Integrated Weep Holes to prevent moisture accumulation

Location:

Westfield, Indiana

Architect:

krM Architecture

Railing:

Post and Wall Mounted Handrail, Structural Glass Railing, Interna-Rail®

Infill:

Glass

Location:

Waynesville, Ohio

Architect:

LWC Incorporated

Railing:

KLEAR™, QUAD™, ADA Compliant Handrail, Glass, Post and Wall Mounted Handrail

Infill:

Glass

Finish:

Dark Bronze Anodized Railing Combination with Clear Tempered Glass Infill Panels and Grab Rail

Location:

Fishers, Indiana

Architect:

Browning Day

Railing:

Interna-Rail®, VUE™, QUAD™, Button Glass Railing, ADA Compliant Handrail, Post and Wall Mounted Handrail, Smoke Baffles

Infill:

Picket, Glass

Location:

Greenwood, Indiana

Architect:

Fanning Howey/Lancer+Beebe

Railing:

VUE™, Interna-Rail®, Post and Wall Mounted Handrail, ADA Compliant Handrail

Infill:

Wire Mesh, Picket, Glass

Finish:

Clear anodized picket railing, red powder coated wire mesh railing and clear glass railing

Hollaender's new Interna-Light™ illuminated aluminum railing system uses LED fixtures (LEDpod™) to produce point source lighting that meets decorative or IBC egress lighting codes, as required in all states. PE stamped calcs and/or drawings available at an additional charge.

Location:

Columbus, Ohio

Architect:

Bernardi + Partners

Railing:

VUE™, Interna-Light™

Infill:

Glass

Finish:

Grey powder coat finish railing with 3/8" thick tempered glass

Location:

Atlanta, Georgia

Architect:

HGOR

Railing:

Interna-Rail®, Interna-Light™, Post and Wall Mounted Handrail

Infill:

Wire Mesh

Finish:

Illuminated railing with clear anodized finish frame with e-coated and powder coated 2x2" steel wire mesh infill

Location:

Omaha, Nebraska

Architect:

El Dorado Architects

Railing:

Post and Wall Mounted Handrail, ADA Compliant Handrail, Interna-Light™

Finish:

Stainless steel handrail with LED Pod lighting

The structural glass railing has an extruded aluminum shoe that is encased with cladding that can be either stainless steel or aluminum. Top caps or rails are available in round and U-channel forms in materials and finishes that match the cladding as well as the assist rail. Wood is a popular option.

• Cladding can be stainless steel or coated aluminum.
• Top rails, caps and assist rails are available in stainless steel, aluminum and wood, in a variety of different shapes and profiles.
• Glass can be monolithic or laminated, clear or tinted in a variety of shades, ½" to ¾" thick.

Button Glass Railing is an engineered railing system designed for side mounting to adequate structural mounting surface giving the impression of a “glass wall".

The glass railing, typically 42 inches high above the walking surface, is point or button mounted to stringer on level or stairs. Since the actual height of the glass above the button mounts is in the order of 48 to 52 inches, the glass must be structurally sound enough to meet code and be “comfortably safe". Due to the height, glass is either ¾" thick in monolithic or 13/16" thick in either PVB or SGP laminated.

Buttons are typically 7 inches apart in the vertical orientation, so stringers or mounting surfaces must be adequately sized to take this dimension.

The glass railing comes with stainless steel assist rail for stairs, and can have a variety of top caps, as well as using the top of the glass with no cap as an option.

Please refer to our standard details to determine suggested mounting surface dimensions.

Smoke baffles can be mounted directly to the ceiling or may be concealed behind the ceiling. In either case, installation is easy and cladding can be selected to match the surrounding aesthetic.

Our smoke baffles are engineered to meet the National Fire Protection Association's (NFPA) standard for installation of sprinkler systems (Chapter 13) as well as IBC 2012/712.1.3.1 Fire and Smoke Protection Features. 

Hollaender® railing systems are installed in every geographic region of the U.S. and in a variety of applications. We have a long history of supplying railing systems to such demanding industrial and military customers such as NASA, United States Army Corps of Engineers, and Bechtel. Our customers can be sure that our handrail systems will stand up over time in every architectural application and produce the lowest long term installed cost.